thrasher_565

hmm so im updating my post. instead of me complaining on how mush it costs im just going to post on the build. Pc 1 gaming: cpu: skylake 1151 i5 6600k (in case i want to over clock) Gpu: msi gtx 780 lighting mb: Gigabyte z170-hd3-cf (in case i want to over clock) Psu: old xfx 850 ssd: Mushkin MKNSSDE3480GB Eco3 480 Gb ram: Corsair ddr4 -2132 dominate platinum 16gb (just in case later fined out 8gb is good enuff) Pc 2: surfing the net, Netflix, music Cpu: i7 920 1366 2.66 Gpu: gtx 760/780 mb: asus rampage 2 extreme Psu: non i sold my other one....(stupid me) Hdd: Wd velociRaptor 150 gb ram: 6gb gskill ram ( update only 4 gig out of 6 work 1 slot broken on mb... ) Have to sell the two dark base pro cases My pc right now so first off why the #### not to polish the back? real high quality my ####. second i was going to add an 5mm led stopper on the back...but its g1/8 threaded.... and i did spend $20 for 4x plugs that i cant use. if i do what to use em ied have to get an g1/8 to g1/4 thread adapter and spend even more money (taxe, shipping, border fees, #### fees...) http://www.performance-pcs.com/bitspower-premium-g1-8-high-flow-g1-4-adapter.html never mind trying to find the rare as balls g1/8 led stop they advertise with... (edit i found them and got 4 of them but don't have the g1/8 to g1/4) and how do i empty it? if i want to do it with an tube ied first have to buy the 4x adapter then buy another 4x $15 valve's and most like need a male to male thread adapter on the valve .... on and on and on and it may be cool but how do you mount it is another problem. i guess this is the best way for now. ill just have to mount one pump on the 2 hole plate and put the psu in the pedestal? would need psu extetions too. but then ied have to mount the rads in the case. it would be a shame to cover up the nice rads thow... im trying to make it so i can just open an valve and have all or most of the water flow out. would mounting the rads in the case make this a problem? i do no that the drain port has to be at the lows point and all the liquid would need a way to flow downward. any tips would be nice plz and thx Edited July 13 by thrasher_565 any way trying to find out how to lay it out Making an much need cut. http:// Geting rid of that stupid bar that block's your HDD rods. http:// This ones on the pedestal. http:// Drill out the rivets http:// Drilled 120mm holes for rad. 8 out of the 12 screws should be ok... http:// http:// G1/4 5mm led stopper with rgb led http:// G1/8 5mm led stopper with rgb led http:// http:// Gtx 780 msi lighting with ek waterblock probly going to sell it and get a 1070 http:// http:// Rads mounted in the case http:// Be quiet shadow wings sw1 says 300,000 hours about 23 years or 6 year warranty Weill see... http:// 4X 4pin to 3 pin pwm (converts 3 pin fans in to pwm) 2X 10 fan hub uses pwm and rpm form mb and molex for power http:// 20 led power molex dont no if i will use it and i would need 3 more... http:// g1/4 pump (think you can use it to suck water out and get it flowing? g1/4 funnel 4X g1/4 ball vale g1/4 long panel mount g1/4 t http:// 1/2 male to male t y 90 http:// http:// should be all the fittings i need.... http:// flow http:// 4X g1/8 5mm led stops 10X g1/4 5mm led stop 22 gadge wire 5mm orange led 5mm rgb led orange barb orings orange dust caps ganaric 4 pin (should work thow) 5X g/14 tip prob stoppers pci digital out (might mod it to work with my mb since it did not come with one but dose support it ) http:// fans mounted to the rad what fun that was....not. because of there stupid gray rubber around the fan you can put then agents each other so i had to use nuts to off set it... http:// http:// http:// the 120mm shrouds have 4x 5mm led holes i might attempt to put rgb leds in but i sux a soldering. i have an idea to use a ribbing cables like ide cables other mods i was thinking of are a volt meter and an rpm meter but dont no how i would do it. was think of a togle swiich to select what part i want to read out so having 1 volt meter and 1 rpm meter for everything. i did order a black 2 slot pci from mouton mods but have not got it yet. want to do a vertical gpu. other mods was to make my own dust cover out of plexy glass and use standoff to mount it. then use thermaltakes 16x pcie extension and a 16x 90 riser but that's a lot of money haha weill see.