Jump to content

Project Open Core: Liquid P5, Hardline Tubing, Illuminated System Panel


Mr_Armageddon

Recommended Posts

Project Open Core: Hardware - GPU

As stated in the OP, part of the reason I decided to build this sytem was to put together the hardware to provide a good VR experience with the Oculus Rift.  Being that the GPU is the most important factor in this, decided and upgrade from my GTX 970 was in order.

Timing worked out pretty well, as Nvidia recently released their “Pascal†cards, and I was lucky enough to snag an EVGA GTX 1080 SuperClocked Edition card from Newegg’s first available batch.  Didn’t even have to wait in a queue.  Since that particular card although overclocked out of the box still retains the reference PCB design, I picked up an EK Waterblock and Backplate to go with it.

27419215730_d5e4876590_c.jpg

I have to hand it to EVGA, they made a really good looking card with the 1080.  Even though the stock cooler and backplate are coming off, wanted to take a sec to show what the card looks like before it gets “nakedâ€.

27087093373_7b74be2ee2_c.jpg

Removing the cover was very simple, and I was surprised to see a location where LED lights plug into the PCB.  On this particular version, the LED is white only, and the EK block covers the pins, so I didn't pay it much mind.   EVGA ships some sort of pre-shroud that goes between the cooler and the card.  It actually looks really cool, and it would have been great to be able to incorporate it into the water block, but they aren’t compatible, so it had to go.  

Behold a naked GTX 1080 SC. Important to note, that the stock EVGA backplate will NOT work with the EK Waterblock.  I had to purchase the EK backplate separately.

27419215110_f0e0ef9c66_c.jpg

This particular EK block is the Nickel & Plexi combo. I like the look of the nickel, and wanted to be able to see the fluid as it goes through the block, so this really was my only option.  I wish they made one that was a nickel / acetal / plexi combo that looked all black, but still showed the fluid in the middle. Since they don’t make one, I did a few mods to achieve that look.

27087092793_ab1e4b9bc9_c.jpg

Here we have the card installed and a quick fluid test to see how it looks… and it looks great!   The backplate is very nice as well.

27596735362_92536da123_c.jpg

I wanted the fluid to glow blue in this card, and was initially planning on using the two pre-drilled 3mm holes for LEDs on the block. Gave them a shot, and found they are too bright of a focal point, and wash out the color of the fluid as seen below.

27523215631_52ac623767_c.jpg

As a solution, I decided to add more RGB LED strips to both the GPU and CPU Waterblocks. Not oly does this allow me to get the color to match what I have going on around the case, but I can also tone down the brightness levels to a point where it just glows but doesn’t blind you.

27605092256_a4a4b94039_c.jpg

As nice as the photo above looks, all the little circles and cutouts glowing was a bit too distracting for my taste, so I went about using Carbon Fibre Vinyl to wrap the face of the block.  It worked really well, and helps focus the attention on just the fluid, and also glows around the exterior of the block similar to how I have the case setup.  They go really well together.

27605089146_8d1fe2a409_c.jpg

I drained the test fluid and installed the card on my case.  It looks really good sitting where it does, and as can be seen below in both the CPU and GPU blocks, the subtle blue glow really works well.  Can’t wait to finish my tubing so I can get some coolant running through this build!

27087092203_67312bd545_c.jpg


For High Resolution versions of all photos from this build log, pleas check out the Album on Flickr.
https://www.flickr.com/gp/24705522@N05/yB94Z9
.
.

 

Link to comment
Share on other sites

Project Open Core: Hardware - Displays & Peripherals

I am working on wrapping up hardline bends and sleeving, and will post on those topics once completed. As my last “Hardware†post, going to run through my Displays & Peripherals.

I am a consultant, and about 50% of my job is on the road.  When not traveling I work from home. For my setup, I went with a custom Sit/Stand desk with motorized legs.  I usually start the day standing, but by 2-3pm, the knees start to ache a bit and I drop the desk and pull up a chair.  My displays are wall mounted, on articulating arms.  Although I can adjust them to my heart’s content, I have found a good location for them that I can use while standing or sitting, so they never move.

27707092356_2c9bb1a09a_b.jpg

Using 3 monitors currently in a PLP configuration.

  • Primary Display - 30in Dell 3011U @ 2650x1600
  • Side Displays - 20in Dell 2007FP @ 1200x1600  (x2)


Total resolution is 3850x1600, which gives me a lot of good workspace.  Here is what the desktop looks like in a seamless “Print Screenâ€.  Using Display Fusion to manage my wallpapers, and a few Rainmeter “skins†to customize the look of the desktop and give me system stats at a glance.

15333089482_d3b105a1f1_b.jpg

Keyboard and mouse using a Corsair K70 RGB Mechanical Keyboard, and a Logitech G502 Mouse.  Both utilize RGB LEDs, and are customizable.

The newest addition to my setup is the Saitek X-56 Rhino H.O.T.A.S. Flight Controller.  I have been getting into Space Sims lately, and this has been a huge upgrade from my old but trusty Logitech Extreme 3D Pro joystick. The difference the new X56 has from the X55 is two additional thumb control sticks for your thumbs, specifically helpful for extra control with space sims, and the addition of RGB lighting.

27666385321_971fa55e62_c.jpg

Here is a pic of all of them together.  Really liking that manufacturers are going with RGB lighting so you don’t have to settle for whatever color they decide to ship units with.  Very easy to match the colors of the new build.  Customization FTW!

27666385901_aa293c2331_c.jpg

For High Resolution versions of all photos from this build log, pleas check out the Album on Flickr.
https://www.flickr.com/gp/24705522@N05/yB94Z9
.
.
 

Link to comment
Share on other sites

Slight Problem, need help

I was planning on testing all of my wiring since I made the majority of the PSU cables myself, and ran into a bit of an issue.  Everything powers on well, lights up, pumps work, etc.  But the ASUS MoBo will not fully boot.  Keep getting an error saying  "USB Device Over Current Status Detected" and an error code on the motherboard of "55".  

A Google search tells me Code 55 is "Memory Not Installed", but as can be seen in the picture below, the RAM and CPU are fully recognized.  Plus, I don't see what that would have to do with the USB Over Current Error.

27722497656_4f253a8468_c.jpg

I have also unplugged everything from the motherboard (including front case USB headers) except the keyboard and mouse.  No Drives, GPU, or fans are plugged into the motherboard.  I have tried various USB ports, and have even tried different keyboards.  Keep getting the same error, and cannot get into the BIOS at all.

Any feedback or suggestions would be greatly appreciated, as I doubt I will hear back from ASUS for a few days. Thanks.

Link to comment
Share on other sites

Issue Resolved… sort of

After trying what seemed like everything I could think of, along with some suggestions from people on various forums, finally figured out what the issue was.  I thought I had unplugged everything in my search for a fix, but I missed the PCIe USB 3.1 card, mainly because it was hidden behind the PCIe Riser Cable going to the GPU with its vertical installation.  I couldn't see it, and passed it over.

The reason that particular card was giving me issues was due to the fact that USB 3.1 can draw a lot more power than 2.0 and even 3.0, which it what was triggering that particular error message, and causing the reboots.  I went ahead and made a new SATA Power cable and added it to the expansion card, and the power / current issues are gone.

I have finished a few test, and was even able to install Windows 10 while checking for fluid leaks.  Still having an occasional issue during boot up, but I know that cause this time of the Q-Code 62.  That same PCIe Riser Cable that hid the USB Card, is causing the boot process to lock up.  As soon as I unplug the card, everything functions as it should.  I have been reading that adding extra shielding to the cable can fix the issue, so going to give that a shot.  If not, will have to hit up Thermaltake for a new cable.  I really hope it will be a quick fix, as the build is almost done and I  would hate to have this hold things up.

27502667140_012d26dbd9_c.jpg
 

Link to comment
Share on other sites

Project Open Core: Hardline Tubing

For this build, I decided to go with Monsoon Hardline PETG Tubing 1/2" ID, 5/8" OD.  I initially had purchased PrimoChill PETG Tubing, but decided that the diameter was too thin and liked the look of â…†OD better.  This is my first time “tube bending†so I purchased a lot of it since I knew that I had to account for the varoius screw ups that would occur.  Luckily it is not very expensive.

27502718920_71a8c2b882_c.jpg

Since it was my first time working with hardline tubing, I had to acquire a few tools to make sure my bends look good. I already had a few things, like the rotary pipe cutters and a heat gun, but also picked up some Monsoon Mandrels to help form bends, a measuring kit, and a tube bending rig made by Barrow which came in really handy.  

27680395812_4f35c9b567_c.jpg

I have noticed that a lot of people cutting tubing use a hacksaw, but I personally thing the rotary pipe cutter is a much better tool.  Not only does is make very straight cuts, but it leaves no mess, and gives the tubing a nice beveled edge as can seen in the picture above, and ensures I don’t damage the o-rings when sliding them on for the fittings.

The Barrows bending rig was very useful when doing more complex / multi angle bends, and assured not only my angles were dead on, but that the tubing was straight throughout the level plane I was working with.  It also allowed me to keep things stable when doing larger 180 bends than what the Monsoon mandrel kit supported.  Used a can of compressed air as a form for one of the bends, and it come out really nice.

27502713830_bc220862b5_c.jpg

For the most part, my bends held true to my original 3D render which I was glad to see.  One place where I had to simplify a bit is where the Motherboard outlet connected to the GPU block. I was initially going to go with a nice multi-bend solution, but realized after installing the fittings that my plan wouldn’t work.  There wasn’t enough clearance between the fitting and the motherboard housing to do a 90 degree bend from that location. So I used my measuring kit to form a more simple
“L†bend directly to the GPU block.  

27680393572_d7c850120f_c.jpg

Not as fancy, but the end result still looks great.  Towards the end of the process, I was getting really good and quick at making quality bends.  I may change things around at some point, but for now, I am happy with the end result.  Time to move on to finishing up making some power cables and getting them sleeved.

27706603891_aab2090cc2_c.jpg


For High Resolution versions of all photos from this build log, pleas check out the Album on Flickr.
https://www.flickr.com/gp/24705522@N05/yB94Z9
.
.

Link to comment
Share on other sites

This is amazing man!  Puts my recent P5 build to shame, lol.

 

I'm curious, did you add additional shielding to the provided 16x riser cable?  My rig is currently almost unusable due to consistent driver crashes.  I've narrowed it down to the riser cable.  If I power down, and monkey with the bend radius of the cable a bit, I can run benchmarks, watch youtube vids, etc without issue...for a bit.  Then all of a sudden I'll start getting driver crashes doing simple things like web browsing.  I tried hitting up Thermal Mike's post about getting a new cable, but have received no response.

 

Are you having issues with the cable provided?  Or did you get a new one?

 

Here is a couple shots of my build - nothing near as sweet as yours (I have the same ASUS mobo, and I really like it - especially the lighting control - mine is controlling the lights under the desk):

 

BD4Btu6.jpg

 

cXTuyLG.jpg

Link to comment
Share on other sites

This is amazing man!  Puts my recent P5 build to shame, lol.

 

I'm curious, did you add additional shielding to the provided 16x riser cable?  My rig is currently almost unusable due to consistent driver crashes.  I've narrowed it down to the riser cable.  If I power down, and monkey with the bend radius of the cable a bit, I can run benchmarks, watch youtube vids, etc without issue...for a bit.  Then all of a sudden I'll start getting driver crashes doing simple things like web browsing.  I tried hitting up Thermal Mike's post about getting a new cable, but have received no response.

 

Are you having issues with the cable provided?  Or did you get a new one?

 

Here is a couple shots of my build - nothing near as sweet as yours (I have the same ASUS mobo, and I really like it - especially the lighting control - mine is controlling the lights under the desk):

 

BD4Btu6.jpg

 

cXTuyLG.jpg

 

I am actually using the 2nd version of the cable that Mike already sent out.  I too am having issues (can't even boot up) when the riser card is used.  I have emailed Mike again a few days ago, but haven't heard back.  :( 

 

I am going to try and add extra shielding to see if that helps.  I really like the idea of the vertical card installation, but so far in practice it is proving to be a poorly executed idea.

Link to comment
Share on other sites

Bummer man - I can at least boot up - but all intents and purposes, I might as well not be able to.  Let me know if you try more shielding and it works.  I've heard it can also be the bend radius of the cable - has to be a smooth bend.  I tried that after reading about that and got things working, if only for a bit.

 

I have found a few other cables that appear to be good quality (they look well shielded) I may try.  I went with this case over the Phantec Enthoo Primo because of the vertical GPU mounting, but like you said - seems a poorly executed product so far.  If I can't get the new cable (or get it work), and getting a new third-party cable doesn't work out - I'll have to drain the GPU loop and do a normal horizontal mount, thus having to re-do my bends, and that was a bit tedious for me, lol.

Link to comment
Share on other sites

So, I've decided to give this a try:  https://www.amazon.com/gp/product/B01CEIEWU4/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

 

Reviews seem MUCH better.  I won't get it for a few weeks due to back order (edit: I just happened to check it again and noticed it now suddenly said in stock!  so I'll have it by Friday) -I'll let you know if it works out.

Link to comment
Share on other sites

So, I've decided to give this a try:  https://www.amazon.com/gp/product/B01CEIEWU4/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

 

Reviews seem MUCH better.  I won't get it for a few weeks due to back order (edit: I just happened to check it again and noticed it now suddenly said in stock!  so I'll have it by Friday) -I'll let you know if it works out.

I actually had that same cable in a wish list since it said as of yesterday, not available. When I clicked the link to see if it was the same one, they had them in stock. Mine will be here Friday as well!

 

Really hoping it fixes the issue. If not going to try the more expensive Lian-li cable which is similar tobthe ilone made by 3m.

Link to comment
Share on other sites

Project Open Core: Sleeving

My last build incorporated sleeving from MDPC (MurderMods), and it turned out really good.  I still have a lot of sleeving left over from that project, but decided to try something different for this build. I have heard a lot of things, both good and bad, about Paracord sleeving, so I decided to do a sample to see if it would work for this build.  As I mentioned before, I like MDPC sleeving, but I find it a bit stiff to work with at times.  So I purchased a few hundred feet of coreless paracord, which cost less than $25, and got started sleeving.

In addition to the custom sleeving, I typically make my own power cables for each build.  I find by doing this I am able to limit all the extra cable length taking up room in the case, and it allows for better looking cable routing.  Here is a pic of the primary tools used for the job.

  • Paracord (Black)
  • Paracord (Royal Blue)
  • Paracord (Slate Grey)
  • Lutro Paracord Sleeving tool (makes job snag free)
  • 100ft 18AWG Wire
  • PSU Power Connector Pins (lots)
  • MDPC Crimping Tool
  • MDPC Pin Extractor
  • Molex PSU Connector Heads (Various)
  • Precision Titanium Snips
  • Hobby Knife
  • Bic Lighter

27764136212_04eb393dc7_c.jpg

After doing a few trail runs and deciding that I really like using Paracord, I set to work making my cables. In addition to looking great, and being very flexible, I like that with Paracord I can sleeve the cables without having to use heatshrink.  I personally think it looks cleaner, and it cuts down the time required to get the job done.

27830827986_48561e7015_c.jpg

For most of the build I am using “Wire Wraps†that are 3D printed by Ensourced. I find they are really easy to work with, and look great once installed.  They do a good job of keeping the sleeved cables tidy, especially when doing bends.  

Here you can see a comparison of my new paracord sleeved ATX connector vs my older one using MDPC sleeving.  So pretty!

27789496191_14f5022a3d_c.jpg

Here we have another comparison of the two types of sleeving.  Really impressed with the look and feel of the paracord.  Also liking the combination of the 3 colors, and how well it goes with the rest of the build.

27830828246_16de9e5dcf_c.jpg

The cable shown below is one I had to create later on in the process after I was having boot issues caused by me not adding a power connector to my USB 3.1 expansion card.  You can see the cable plugged in the bottom part of this picture as well.  Glad I got that one figured out!

27253531384_aeee32595b_c.jpg

Here we have the final stage of the custom cables and sleeving in all it’s glory.  Really liking how the colors look, and how clean the paracord sleeving turned out.  Cable management in the back is good, but could be better.  May work at securing everything down a bit more once I verify that everything is working the way it should.

27253539944_c5067133cb_b.jpg

For High Resolution versions of all photos from this build log, pleas check out the Album on Flickr.
https://www.flickr.com/gp/24705522@N05/yB94Z9
.
.

 

Link to comment
Share on other sites

I am happy to report that the PCIe riser cable I purchased works perfectly!  No more boot errors, benchmarks work, and I can even OC without issues.

27857899256_ac3ae5d188_c.jpg

Here is the Amazon link if anyone with the Core P5 Case would like to give it a go.  It seems a lot higher quality than the one provided by Thermaltake, and is shielded well. The only problem is that one of the screw holes doesn't line up exactly with the P5 case mount.  I ended up using the screw on the side with the PCIe latch, and a zip tie on the other.  Not ideal, but it works, and doesn't wiggle.

27816021661_bef4a1aa4a_c.jpg

One thing I made sure to do this time is not have any drastic bends, and to not bend anything near the connectors.  Used a can of Pledge Spray as my guide for nice rounded bends.  

27857899626_6778bc21f9_z.jpg

Now that I am back to having a 100% working system, I can work on getting this build finished up!  Time for some leak testing.
 

Link to comment
Share on other sites

Project Open Core: Initial Fill and Leak Testing

Now that the tubing and cables are done, time to fill this thing up with fluid.  Before I did an entire system fill, there were 2 things I needed to do.

Needed to flush the radiator of any particulates.  I have heard in a lot of reviews that radiators can have all kinds of metal shards inside time left over from the manufacturing process.  I detached the radiator from the rest of the loop, and flushed it with distilled water.  Pleased to find very little in they way of particulates, so drained it and reattached the tubing.
Then had to decide on what color of LED I wanted to use in the Res, being that is was one of the few lights in the system that wasn’t RGB.  I filled it up a little over halfway, added a bit of Blue Dye, and first tried the White LED, which is the photo on the left.  It looked good, but wanted to try blue as well.

At first I was worried that the blue would look purple and not match the rest of my system (kinda like it does in the picture on the right).  But in real life, it is the perfect color blue, and seems to light up the entire Res a bit better than the white one, so going to stick with the blue LED for now. Its an easy change if I decide to go with the white sometime in the future.

27309001714_78cab0c91d_c.jpg

After deciding on the LED color, I drained the Res, connected the tubing to the rest of the system, and began filling with distilled water for the first official “Leak Testâ€.  Quick note of filling a system with this XSPC Photon Res… you will need a book, which you can see in the bottom right of my photo below.  The case/res has to be tilted at an angle during the fill process, or the opening will keep backing up with air bubbles.  The first 5 minutes of the fill process were very frustrating until I figured this out.  After sliding a good size book under the right leg of the case, filing became very easy.

Was able to fill the whole system in a just a few minutes, alternating between running the pump and tilting the case to release air bubbles. It looks like it is going to take around 1.4 liters to completely fill the system loop and res.  I then ran it for a few hours, and didn't find a single drop of water outside of the loop.  Leak test completed successfully.

27886604886_622b224e14_c.jpg

For High Resolution versions of all photos from this build log, pleas check out the Album on Flickr.
https://www.flickr.com/gp/24705522@N05/yB94Z9
.
.

Link to comment
Share on other sites

Yep - just came here to report that mine is working as well!  Had a couple minor issues with getting the bend radius correct.  I also had the issue with the screw hole lining up.  I wish I had checked here first!  I ended up draining my loop - which at first I was thinking I could avoid - and in the process, despite trying to be super careful with lots of paper towels, etc, I ended up dripping red coolant on my nice new desk and now it's pretty much ruined.  Luckily my large steele series mousepad covers it up.

 

It got it working, went to move the case back and it acted up again for a few - so maybe in a few months I'll use your mounting method - as I am experiencing a slight bit of droop - but, if it ain't broke, don't fix it, right!

 

I also got a response from Mike at Thermaltake, he is sending me a new one - I may try it out soon when I get another GPU.  If it still doesn't work, I know which one to purchase.  I'm definitely glad it worked, as I was starting to fear I'd have to plug it straight into the motherboard - making the purpose of this case null and void, and I'd have to re-do the tubing bends.

 

I'll check back later and re-read your post about cables and such!  Great work again man!  making already want to plan out some updates for the future (like the wrapping)

Link to comment
Share on other sites

Yep - just came here to report that mine is working as well!  Had a couple minor issues with getting the bend radius correct.  I also had the issue with the screw hole lining up.  I wish I had checked here first!  I ended up draining my loop - which at first I was thinking I could avoid - and in the process, despite trying to be super careful with lots of paper towels, etc, I ended up dripping red coolant on my nice new desk and now it's pretty much ruined.  Luckily my large steele series mousepad covers it up.

 

It got it working, went to move the case back and it acted up again for a few - so maybe in a few months I'll use your mounting method - as I am experiencing a slight bit of droop - but, if it ain't broke, don't fix it, right!

 

I also got a response from Mike at Thermaltake, he is sending me a new one - I may try it out soon when I get another GPU.  If it still doesn't work, I know which one to purchase.  I'm definitely glad it worked, as I was starting to fear I'd have to plug it straight into the motherboard - making the purpose of this case null and void, and I'd have to re-do the tubing bends.

 

I'll check back later and re-read your post about cables and such!  Great work again man!  making already want to plan out some updates for the future (like the wrapping)

 

Sounds good. Curious to see if the new Thermaltake cables are as good as the one purchased from Amazon.

Link to comment
Share on other sites

Project Open Core: Benchmarks & Temps

I am putting together a neat little video of the filling process and adding the Mayhem Blue Pastel dye to the system. While working on that, I had a chance to play with a bit more Overclocking, and wanted to share those specs along with some Benchmarks and Temperatures.

Overclocking was pretty easy on this system.  I was able to hit 4.8GHz on the 6700K fairly easily using a core voltage of 1.375, and temps never got above 58C during stress testing. I tried for 5.0GHz, but no matter how much voltage I threw at it, couldn’t get stable enough to run benchmarks, so stayed with 4.8GHz, which really isn’t that bad with the temps I am seeing.  

With the GPU the highest I was able to get and be 100% stable on the EVGA GTX 1080 SC, was a core clock of 2151MHz and Memory at 5500MHz.  That’s not overly impressive compared to other GPUs in the past, but apparently the Pascal series cards already come out towards the peak of their frequency threshold. Even then, a 24% core clock increase over reference 1080 cards isn’t too shabby, especially being that my GPU temps have yet to rise above 40C.

27887673866_fe1fe477bf_b.jpg

Once I had the CPU and GPU OC’d, it was time to throw some benchmarks and games at it.

Unigine Valley Benchmark 1.0
Setting: Exreme HD
FPS: 120.4
Score: 5038  

27887674086_3eaee2cb32_b.jpg

Unigine Haven Benchmark 4.0
Setting: Extreme
FPS: 101.8
Score: 2563
 
27887673836_ecbc9c6dd2_b.jpg

Ashes of the Singularity
Setting: Crazy, DX11
Average FPS: 65.5

27887673766_14eb23345f_b.jpg

Shadow of Mordor
Setting: Ultra
Average FPS: 174.45

27922117495_9103792c6a_b.jpg

3DMark FireStrike 1.1
Score: 19499
Compare: Better than 982% of all results

27922117005_3192ba42b0_b.jpg

3DMark FireStrike Extreme 1.1
Score: 10735
Compare: Better than 92% of all results

27922117025_39342f8a83_b.jpg

3DMark FireStrike Ultra 1.1
Score: 5807
Compare: Better than 78% of all results

27887673516_0c192c7856_b.jpg

3DMark Sky Diver 1.0
Score: 42539
Compare: Better than 99% of all results

27887673406_b7582d3f3a_b.jpg

For High Resolution versions of all photos from this build log, pleas check out the Album on Flickr.
https://www.flickr.com/gp/24705522@N05/yB94Z9
.
.
 

Link to comment
Share on other sites

My replacement cable from Tt will be here on Thursday.  I'm debating if I try to test it right now, or not....

 

if I don't have to drain my loop, I may try it out.  Otherwise, I'm putting the bracket back on (using your zip tie method) and calling it a day.  I have had a few boot issues with the new cable, but I think it may be because I don't have the bracket in place and am getting some sag that may be putting a tad too much torque on it.

Link to comment
Share on other sites

Project Open Core: Final Build Pics

This build is DONE!!  That doesn't mean I won't make any changes, as I am a constantly tinkering with things, but the core system is ready to go.  I still need to moidfy a few things at my desk and route cables before I move it over, but still calling the project done at this point.

Not really any reason to describe each picture, so just going to post a bunch of them from different angles.

27731647890_92e79cae0c_b.jpg

27928987041_1bf2c9ec38_b.jpg

27392913423_a9e69f3ba8_b.jpg

27928987371_0182c07f34_b.jpg

27928986851_754de8e198_b.jpg

27928986671_0879a6bcf7_b.jpg

27392914313_fbab082b8a_b.jpg

27928986451_da6cf7d4ea_b.jpg

27707092356_2c9bb1a09a_b.jpg

27392912653_a6eb90a278_b.jpg

27392912203_1c7f062d0b_b.jpg



For High Resolution versions of all photos from this build log, pleas check out the Album on Flickr.
https://www.flickr.com/gp/24705522@N05/yB94Z9
.
.

Link to comment
Share on other sites

  • 2 weeks later...

I moved the new build from the "tinker" room to my actual office setup.  After connecting everything, it was apparent that I needed to do some much needed cable cleanup behind the standing desk. Purchased a few cable racks, and the end result is greatly improved. Dubbing myself "Cable Lord" after that cleanup job.

28156673710_64566fa93a_b.jpg

Link to comment
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...