cabchop Posted February 10, 2017 Report Share Posted February 10, 2017 Hello forum. First time poster. Just purchased the Riing plus three pack of fans. First impression: These are gorgeous fans. Wow.... is all I can say. Still playing around with them, but so far very impressed. The controller and software seem to have a few bugs. One issue I have noticed is I get a Controller Warning each time I make any change to the fan configuration and save it. The configuration changes are saved, but a warning message pops up (image below). The warning also pops up when I load the software. I left the controller jumpers on default since I only have one. I've also run into problems with my Corsair software since I installed the Riing Plus software. The Corsair software (RGB for keyboard and mouse) does not operate anymore. Not sure what the issue is but thought I'd check here to see. Will continue to monitor and update. Thanks. Quote Link to comment Share on other sites More sharing options...
quincy314 Posted February 16, 2017 Report Share Posted February 16, 2017 try turning off fan 4 and 5 if you are not using Superdave67 and cabchop 2 Quote Link to comment Share on other sites More sharing options...
cabchop Posted February 16, 2017 Author Report Share Posted February 16, 2017 try turning off fan 4 and 5 if you are not using Thanks for the advice. Worked perfectly. Didnt even know they were on until I read your post. Much appreciated. Quote Link to comment Share on other sites More sharing options...
Jedson3614 Posted February 22, 2017 Report Share Posted February 22, 2017 My fans spin, power up, and display RGB, but the software is unresponsive, I get 0 RPM and have no ability to change any colors. I have done a bit of research into these fans and the previous ones. Have any of you experienced these issues, or found a work around! Quote Link to comment Share on other sites More sharing options...
Superdave67 Posted May 16, 2017 Report Share Posted May 16, 2017 On 2/16/2017 at 3:53 PM, cabchop said: Thanks for the advice. Worked perfectly. Didnt even know they were on until I read your post. Much appreciated. Ditto! At least I think. We'll see, as I just now turned 4 and 5 off. Hopefully that does the trick. Quote Link to comment Share on other sites More sharing options...
meskline Posted September 7, 2017 Report Share Posted September 7, 2017 Hello people! I wanted to consult you because I have the same problem. I have 4 coolers connected but I do not know how to disable the 5 cooler so I do not throw the warning message. Sorry for the ignorance and thanks of anteamano. regards Quote Link to comment Share on other sites More sharing options...
TZero Posted September 7, 2017 Report Share Posted September 7, 2017 13 hours ago, meskline said: Hello people! I wanted to consult you because I have the same problem. I have 4 coolers connected but I do not know how to disable the 5 cooler so I do not throw the warning message. Sorry for the ignorance and thanks of anteamano. regards Open the software and go to inexist fan Click this symbol above to disable Quote Link to comment Share on other sites More sharing options...
meskline Posted September 7, 2017 Report Share Posted September 7, 2017 Thank you very much. Now I could disable it as there is no more error message Quote Link to comment Share on other sites More sharing options...
S1xstring Posted September 15, 2017 Report Share Posted September 15, 2017 I literally made an account just to respond to this thread...THANK YOU! I honestly can't believe I never googled this before and I've ALWAYS had this error. Who knew it was such a simple fix. You're a lifesaver. Quote Link to comment Share on other sites More sharing options...
TZero Posted September 15, 2017 Report Share Posted September 15, 2017 You're welcome !!!! We are in the same boat Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.