[Alternative to TT RGB software]

17 hours ago, Teszty66 said:

Yes they should work fine. Although they have 9 leds and the software assumes 12 leds so some rgb modes might behave weird.

Right now I’m running version 1.7 of the old software and it’s perfect. I haven’t had a chance to sit down and look at the config for the new service. It doesn’t look too difficult with a basic understanding of how this stuff works. After I figure the configs out, I’ll switch to the new software probably. 

I just want want to say thanks. I spent $60 on these fans and for TT’s crap software not to work at all was really frustrating. With yours I have even more control than I did before. Between the software interface and extra control your software is everything that TT’s should have been. The only thing I’m a little upset about loosing is the Razer Chroma sync (but it didn’t work in the first place so in reality, it’s not a problem).

Anyway, I’m looking forward to messing around with custom effects and I hope you continue development.

[Alternative to TT RGB software]

1 hour ago, Teszty66 said:

That might just be the way the controller is programmed, since you cant pass to the controller how many leds a device has, so I think it also assumes 12 leds per device. Thats why I said to try with the full black, maybe it detects the black as limit for leds.

 

Hmm that sounds like it does not set the speed then. Unfortunately the old app only sets the speed by percent.

The RPM going to 0 and back might be a conflict with another software, at least this is what was happening to RPM of my fans when I had the service and the official app running, they were both writing to the controller and it was freaking out. If the fans also see this behavior check if the official software is running. Aida64 added support for TT fans some time ago and it also causes this issue.

Ooh I see, so the pump is also connected to the PWM of the motherboard. I guess that means you can only configure rgb on the AIO and the pump is controlled by the motherboard speed controller. But that does not explain why it goes to 0 RPM. Does it also happen when you stop the service? Maybe you can control the speed but the TT controller and the motherboard controller are interfering with each other.

 

Dont know if I will be making a GUI for the new one since its a lot more complex. And you should check github if you want updates about the new version, I wont be posting about it here.

 

Yes they should work fine. Although they have 9 leds and the software assumes 12 leds so some rgb modes might behave weird.

Okay thanks. I’ll be installing later today and I’ll let you know how it goes.

[TT RGB Plus Freezing/Unresponsive]

On 12/11/2018 at 8:15 PM, jfs113 said:

let me know if you find a fix, for some odd reason, other then one of the newer versions, the TT RGB software freezes up my computer on start up? nothing with work and have to hard re start into safe mode to unistall software.

 

it worked fine for about 3 months and i have no new hardware but somthing is not liking TT RGB.

I’m having a very similar, possibly the same problem. If I have the software installed, my PC will freeze up. The mouse moves and it acts like I can click on things but the buttons don’t do anything. After uninstalling in safe mode all problems go away.

IF windows runs stable with the software installed the RGB control only works for a few seconds to a few minutes before the effects and speed control just stops. Opening the software, it’s like Windows, all of the buttons are there but the don’t actually do anything

[Alternative to TT RGB software]

Any chance in #### this software will work with the pure plus fans?

I’d appreciate it if you’d check out my thread and let me know if this software would help with my problem.

Thanks in advance!

 

 

[TT RGB Plus Software Gets Stuck]

Hey, I'm getting frustrated. This my first experience with TT and so far I'm not impressed. I have the Pure Plus 120mm RGB fans. Out of the box, setup was easy hardware wise. After installing the software, I started having problems. For the first 30 seconds, the software runs I'm pleased. Then the RGB effect on the fan stops, as in it freezes in the exact spot it's in. I end the task in task manager and start the software back up. Fine for the first 10 seconds. The RGB works, I'm getting fan speed, but then the fan's RGB freeze again and the RPM numbers freeze too. All of the buttons still work but it's like the program forgot what it's supposed to do. After restarting the computer I get the same results. I checked all of the connections to the included RGB controller and they are all good.

From what I can conclude, the connection between the controller and the PC is weak, this is just a guess but that's all I can come up with. Any ideas?

 

Specs:

Ryzen 3 2200g

ASRock A320-DGS

Zotac GTX-1060 3gb

8Gb G.skill Ripjaws 5 2400mhz