Jump to content
  • Forum Statistics

    7.5k
    Total Topics
    54.6k
    Total Posts
  • Member Statistics

    134,659
    Total Members
    16,800
    Most Online
    Erica
    Newest Member
    Erica
    Joined

dwarak

Members
  • Posts

    2
  • Joined

  • Last visited

Contact Methods

  • Website URL
    http://www.besanttechnologies.com/training-courses/java-training

Profile Information

  • Gender
    Male

dwarak's Achievements

Beginner

Beginner (1/10)

0

Reputation

  1. It's hard to believe that heatsinks for Intel and AMD microprocessors could get any bigger, but that's exactly what's happening. 2012 marks the year of "the really big heatsink" and Thermaltake's Frio Extreme is the latest example of this trend. The Frio Extreme is a large twin tower heatsink with two massive 140mm fans and a commanding foot print of 150mm square! Standing 161mm tall and weighing 1.23 kilograms, the Frio Extreme is destined for full tower gaming cases with plenty of room to spare.
  2. Step 1 — Lower Case Remove the following ten screws: Three 14.4 mm Phillips #00 screws Three 3.5 mm Phillips #00 screws Four 3.5 mm shouldered Phillips #00 screws Step 2 Use your fingers to pry the lower case away from the body of the MacBook near the vent. Remove the lower case. Step 3 — Battery Connection Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board. It is useful to pry upward on both short sides of the connector to "walk" it out of its socket. Be careful with the corners of the connectors, they can be easily broken off. Step 4 Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work. Step 5 — Optical Drive Use the flat end of a spudger to pry the AirPort/Bluetooth ribbon cable connector up from its socket on the logic board. Step 6 Carefully pull the camera cable out of its socket on the logic board. Though not recommended by iFixit staff, some users opt to omit this step completely. For information on this, see the step comments. Pull the cable parallel to the face of the logic board. Pulling it upward may damage the logic board or the cable itself. Step 7 Carefully move the AirPort/Bluetooth ribbon cable out of the way as you peel the camera cable off the adhesive securing it to the subwoofer and the AirPort/Bluetooth bracket. De-route the camera cable out from under the retaining finger molded into the AirPort/Bluetooth bracket. Step 8 Use the tip of a spudger to pry the antenna connector closest to the logic board up from its socket on the AirPort/Bluetooth board. De-route the antenna cable from under the finger molded into the AirPort/Bluetooth bracket. Step 9 Remove the following five screws: Two 10.3 mm Phillips screws Two 3.1 mm Phillips screws One 5 mm Phillips screw Step 10 Pull the AirPort/Bluetooth assembly and the Subwoofer upward near the center of the side of the optical drive until they clear each other. Move the AirPort/Bluetooth assembly and the subwoofer away from the top of the optical drive. Step 11 Pull the right speaker/subwoofer cable out from under the retaining finger near the side of the optical drive. Pull the right speaker/subwoofer cable upward to disconnect it from the logic board. Step 12 Use the flat end of a spudger to pry the hard drive cable connector up from its socket on the logic board. Bend the hard drive cable away from the optical drive. Step 13 Use the flat end of a spudger to pry the optical drive connector up from its socket on the logic board. Step 14 Remove the three 2.7 mm Phillips screws securing the optical drive to the upper case. Step 15 Pull the optical drive upward from its edge closest to the display and remove it from the upper case. Step 16 — Optical Drive Pull the optical drive cable away from the optical drive. Be sure to pull on the connector, not the cable itself. Remove the two black Phillips #0 screws securing the small metal mounting bracket. Transfer this bracket to your new optical drive or hard drive enclosure. Step 17 — Dual Hard Drive Remove the plastic spacer from the optical bay hard drive enclosure by pressing in on one of the clips on either side and lifting it up and out of the enclosure. Step 18 Make sure that the hard drive connectors are facing down before placing it into the enclosure. Gently place the hard drive into the enclosure's hard drive slot. While firmly holding the enclosure in place with one hand, use your other hand to press the hard drive into the enclosure connectors. Step 19 Once the hard drive is snug, reinsert the plastic spacer while holding the hard drive against the bottom of the enclosure. Step 20 Use two Phillips #1 screws to secure the drive to its enclosure. Step 21 Attach the optical drive bracket to the new enclosure with two Phillips #0 screws. Reconnect any cables you have removed from the original optical drive onto the optical bay enclosure. Step 22 Don't ditch that drive! You can still use your optical drive externally with the help of our SATA Optical Drive USB Cable. Align the cable's SATA connector with the drive's port and plug in securely. Plug the USB connector into your laptop and your optical drive is ready for use. http://www.trainingintambaram.in/java-training-in-chennai.html
×
×
  • Create New...