Rakesh Sharma Posted December 3, 2016 Report Posted December 3, 2016 UPDATE : 03-Dec-2016 Build progress on full speed. Working on finishing the top air flaps. LDC controller and micro-controller boards installed working on wiring and connection layout. Hope to finish top panel wiring soon. Quote
Jos214demi Posted December 3, 2016 Report Posted December 3, 2016 Wow! Those tubes on the sides are awesome! Quote
Rakesh Sharma Posted December 5, 2016 Report Posted December 5, 2016 UPDATE : 5-Dec-2016 Full Sunday working… from printer scrap parts to fully working top-air flap transition done successfully., just slight fine-tuning required. https://youtu.be/f-fcIrrcoE8 Quote
Rakesh Sharma Posted December 7, 2016 Report Posted December 7, 2016 UPDATE : 07-Dec-2016Front analog control panel part done. Everything working fine. RPM meter is displaying fan RPM. Under 5000 RPM meter displays accurate fan RPM, but above that it starts showing higher values of RPM.. some fine tuning in Arduino code will solve the issue. https://youtu.be/dGreX0gL20c Quote
filipadrian1980 Posted December 8, 2016 Report Posted December 8, 2016 Good luck! Good job ! Rakesh Sharma 1 Quote
ashleybog Posted December 8, 2016 Report Posted December 8, 2016 good luck bro!! Rakesh Sharma 1 Quote
Rakesh Sharma Posted December 12, 2016 Report Posted December 12, 2016 UPDATE : 12-Dec-2016 Slowly pushing the build towards its completion. Installing VGA water block on both graphic cards. Test fitting, everything looks nice so fare. Quote
hotcoolman Posted December 14, 2016 Report Posted December 14, 2016 Can't wait to see it's moving. Quote
Rakesh Sharma Posted December 15, 2016 Report Posted December 15, 2016 UPDATE : 15-Dec-2016 Final tool needed for this build is here, the G1/4 tap. Quote
buz5 Posted December 15, 2016 Report Posted December 15, 2016 wishing u the best result !! merry christmas & a happy new year !! Quote
Rakesh Sharma Posted December 15, 2016 Report Posted December 15, 2016 wishing u the best result !! merry christmas & a happy new year !! Thanks and Merry Christmas to you and your family. Quote
Rakesh Sharma Posted December 17, 2016 Report Posted December 17, 2016 UPDATE : 17-Dec-2016 Making of liquid channel plate from sheets of acrylic. Cutting, drilling and then threading holes for compression fitting installation. Now water channel is cut out from a 12mm thick acrylic sheet and everything is fused together with acrylic cement and installed inside the case. Quote
buz5 Posted December 19, 2016 Report Posted December 19, 2016 merry christmas & a happy new year !! wishing u great result !! Rakesh Sharma 1 Quote
Touge180SX Posted December 20, 2016 Report Posted December 20, 2016 Being in the military, I have to say I love this build so far! Nice job. Rakesh Sharma 1 Quote
Rakesh Sharma Posted December 20, 2016 Report Posted December 20, 2016 UPDATE : 20-Dec-2016 At last PETG tubes installation done. It was easy and perfect. Yellow transparent side panels cut down to proper dimensions, look great. Still cutting marks are visible on side and edges, will be polishing for proper finish. Quote
Rakesh Sharma Posted December 22, 2016 Report Posted December 22, 2016 UPDATE : 22-Dec-2016 Coolant is here. Will be filling the loop soon, but first have to flush the whole loop with Distilled water. Quote
buz5 Posted December 23, 2016 Report Posted December 23, 2016 nice effort and best of luck !! merry christmas & a happy new year !! Rakesh Sharma 1 Quote
FALCO Posted December 24, 2016 Report Posted December 24, 2016 I like it for its originality. Rakesh Sharma 1 Quote
Rakesh Sharma Posted December 26, 2016 Report Posted December 26, 2016 UPDATE : 26-Dec-2016 Now started adding details to the build. Hand cutting the printouts and applying paint, trying to give some rough look. Quote
buz5 Posted December 28, 2016 Report Posted December 28, 2016 wishing u best of luck & a happy new year !! Rakesh Sharma 1 Quote
buz5 Posted December 28, 2016 Report Posted December 28, 2016 wishing u best of luck & a happy new year !! Rakesh Sharma 1 Quote
Idyiboy Posted December 28, 2016 Report Posted December 28, 2016 wow. that was a nice mod! Good luck Rakesh Sharma 1 Quote
Rakesh Sharma Posted January 2, 2017 Report Posted January 2, 2017 UPDATE : 02-Jan-2017 Now build is about to finish. Little video of filling the loop with coolant. Testing system with Operating System and driver packages installation. Some more final tweaks and system will be ready for gaming action. Quote
Rakesh Sharma Posted January 16, 2017 Report Posted January 16, 2017 FINAL UPDATE : 16-JAN-2017 After about three months of planning and building, finally my “Huffer†build completed. For me participating in 2016 Thermaltake CaseMOD Invitational Season 2 is great honor and making this build was real fun. Like to thanks Thermaltake team, forum members and all of you how showed your interest and appreciation for my build. https://youtu.be/cIdEAP_YtHE Video link : THANK YOU Regards, Rakesh Sharma INDIA TurboUser 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.