ThermalMike Posted March 23, 2015 Report Share Posted March 23, 2015 Hi everyone, With the release of our Pacific DIY components and Kits, I wanted to provide a guide focused on the RL240 kit and take you through the installation process to give users an idea of what you will get: RL240 Kit: What you get: - (1) RL240 Radiator 240x120x64mm - (1) PT40-D5 Reservoir + Pump Combo (Includes Hardware) - (1) W1 CPU Water block (Includes Hardware + Thermal Paste) - (1) 4T 1/2" Tubing (6.5ft) - (1) Coolant 1000ml (Red) + Filler Bottle - (6) 1/2" ID 3/4" OD Compression Fittings - (2) Luna 12 Red LED Fans - (1) 24-pin PSU Jumper Here is everything out of the box: Here is the PT40-D5 Reservoir + Pump: When you open the PT40-D5 packaging you will have all the accessories in bags including the mounting hardware. The brackets included allow you to mount the PT40 vertically or horizontally depending on the configuration you want to do. **VERY IMPORTANT** There are set screws on both ends of the reservoir that are to secure the Tube to both ends, these screw do not need to be tightened. Also take note, if you plan to clean your reservoir later, make sure to remove the set screws (Both sides Top/Bottom) prior to removing to avoid causing any stress to the tube when separating. Also take care of the O-rings on both sides to make sure they are in the correct place when putting back together. On the bottom you have the pump speed adjustment that should be set in the "2" position by default. I recommend leaving the speed adjustment alone until you have the system up and running to make any adjustments later. Turing the speed up is only needed when necessary, with the setting of "2" should be enough to support the default kit configuration. Here is all the included brackets and hardware for the PT40-D5 Since I am installing this in our Core V31, I plan to mount this vertically so I have installed the mounting brackets to the pump housing to secure into the chassis floor. Here is a quick look at the Core V31 that we will be installing the RL240 kit Getting ideas on how to place the PT40-D5. (Removed the HDD trays and the bottom ODD for clearance) Now for the (240mm) radiator placement and overview. First you need to remove the orange plastic plugs that came pre-installed. Give the radiator a quick look and make sure everything is ok. Here is the accessories that come included, you get mounting screws for the radiator and for the fans as well as (3) G1/4 port plugs and a wrench tool for easy installation. Before you go through installing everything on the radiator, check the location where you plan to place it and make sure it will work out with the entire system including the water loop to make sure all your fittings and tubing will have proper clearance and your tubing will have proper flow to avoid the tube from pinching around a tight space. It is also a good idea before installation of your radiator to fill the radiator with distilled water and give it a good shake to remove anything left over from the manufacturing process. Fee free to repeat this step as many times as you want until you are satisfied. You can setup the porting anyway you like, for this example I will use the (2) bottom ports on one side for my IN & Out and plug the other (2) bottom ports on the other side with the last plug for the top. Note: Do not tighten the top plug port just yet, you may need to use it for a breather port when filling The wrench is a great tool to use for tightening the ports on your components as the fittings have "slots" on the top so you can use the wrench to tighten and avoid scratching the component or fitting using a standard pair of pliers. The wrench also is designed to help secure the plug ports nicely. Remember, DO NOT over tighten, you will just damage the O-Rings if you gorilla grip the fittings into place. A snug fit is fine. Now we take a look at the W1 CPU block to prepare it for installation to the motherboard. You will get a simple installation guide showing how to install for Intel or AMD type CPU's. Take note of the accessories labeled for each Intel/AMD. Now install the back plate to your motherboard and punch out the foam holes for your CPU Socket type to install the mounting screws to. Once the back plate is installed and the mounting screws are through the motherboard, secure the CPU in place and apply thermal paste. Then seat the W1 CPU block onto your CPU first and make sure everything lines up correctly. When ready set the (4) plastic washers after placing the CPU block. Then install the (4) screw caps and tighten them in the "X" pattern to apply appropriate pressure evenly as you secure the block. These only need to be hand tight and you should be able to tell when each one is secure very easily. Now you can install the fittings on both ports, don't forget to use your wrench! Tte Martin and EkbergDOF 2 Quote Link to comment Share on other sites More sharing options...
ThermalMike Posted March 23, 2015 Author Report Share Posted March 23, 2015 With our (PT40-D5)Pump/Reservoir, (W1)CPU block and (RL240)Radiator installed we can now install the fans for the radiator. Make sure you first know the direction of the air flow on the fan Now for this build, the fans normally install on the inside of the chassis, but since this is DIY.. It is a tight fit and there was no issue with the front panel installed so I decided to mount on the outside giving me a little more room for the PT40-D5 to fit just right. Moving back to the PT40-D5 will install the fittings and install into the chassis. (Make sure you have placement set where you want it first) Here is the part where you come into the loop You will want to do a placement of all your components before you secure everything into place, some components you might have to remove and replace a few times until you get what you want. Take your time! You want to make sure you have everything installed to not only fit for your other components: PSU cables, VGA cards, HDD/SSD to avoid any issues AFTER you have everything cut and installed. Take note on a couple important actions you need to do: 1. You have 6.5ft of tubing, don't waste making incorrect cuts or cutting too soon. Test and take your time. 2. Cut your tube as straight as you can to have the best seal possible. 3. Once you cut your tubing, use that piece for other routing to get a "Rough Idea" 4. When you have a tight spot (Like I did for the bottom port on the PT40) make sure you give enough room to avoid any pinch in the tube. 5. Secure the compression fittings with the tube pressed over the bard side as best as you can to assure a proper seal and avoid LEAKS. Before we start getting some coolant into our system, take some precaution to lay down on paper towels just in case we have any issue with leaks. Take the 24-pin jumper included to attached to your PSU as this will help with powering up the system without using the motherboard to turn the PSU on. Take advantage of the filler bottle included with the coolant in the kit, you can remove the tip off the end for the bulk filling and then add the tip back on for more precision filling until you have the system purged and filled correctly. Start filling the PT40-D5 with the supplied coolant and you will see the reservoir start to fill and some of the tubing that is lower including the radiator.With the other top port removed on the top of the PT40-D5 I added coolant slowly. Once you get the coolant filled above the inner tube in the PT40-D5 (Fill it above the inner tube about half way) you can now switch the PSU on and let the pump start to circulate the coolant throughout the loop. **You will likely have to switch the PSU on/off a couple times making sure to turn it off once the coolant level gets below the inner tube length** Here is what I had left after filling the system to the appropriate levels. You may have to add more later, let the system run and continue to check for any leaks. Once you have the system running for a while and confirm no leaks are present, shut off the system and reconnect the 24-pin to the motherboard and finish installing the rest of your components. Make sure all your cables are routed correctly when installing other components be careful to not put any pressure on your tubing or other component that could cause any issue with the seal of the coolant in the system. This build was made using only the parts provided in the liquid cooling kit, Thermaltake offers many other parts including several different fittings like 45's and 90's to help with a even better fit. Plan out what you want to do, make sure you have everything you need and if you want to try DIY Cooling, think Thermaltake and let anyone here know if you have any questions. Tte Martin and Tt Andy 2 Quote Link to comment Share on other sites More sharing options...
Tt Andy Posted March 24, 2015 Report Share Posted March 24, 2015 Nice guide ThermalMike 1 Quote Link to comment Share on other sites More sharing options...
TT CPM Posted March 26, 2015 Report Share Posted March 26, 2015 Cool guide, it's very useful ThermalMike 1 Quote Link to comment Share on other sites More sharing options...
Tte Jeremy Posted March 27, 2015 Report Share Posted March 27, 2015 Awesome walkthrough and guide Mike! ThermalMike 1 Quote Link to comment Share on other sites More sharing options...
seasixfour Posted October 10, 2015 Report Share Posted October 10, 2015 Hi guys. Recently finished my Thermaltake RL240 build. Just waiting on a couple of 90 degree adaptors to fix the small CPU kink. Current temps are amazing, at stock, both GTX 980 ti cards barely reach 38 degrees on any game/benchmark. Can vouch for Thermaltake quality, that's for sure. Tte Martin 1 Quote Link to comment Share on other sites More sharing options...
buthhero Posted October 4, 2016 Report Share Posted October 4, 2016 hello help me please.i want to know .can it change to use hard tube??????????????? Quote Link to comment Share on other sites More sharing options...
Madhunter Posted August 29, 2017 Report Share Posted August 29, 2017 You can just change out the fittings to Hardline compression fittings and run your hard tubes. Quote Link to comment Share on other sites More sharing options...
TheTechnologyWaffle Posted October 21, 2017 Report Share Posted October 21, 2017 I'm new to this. Can you fit it with side mount brackets into a Cooler Master MasterBox Lite 3 windowed version? Quote Link to comment Share on other sites More sharing options...
bvalente Posted January 2, 2018 Report Share Posted January 2, 2018 what's the best way to add a drain to this setup? i wanted to change out some parts but i realize draining this is going to be a hassle so i want to be prepared for next time Quote Link to comment Share on other sites More sharing options...
kevin david Posted May 19, 2019 Report Share Posted May 19, 2019 thanks for posting this article. it is very useful information. if you want to download autoroot tools check out. Quote Link to comment Share on other sites More sharing options...
aadi Posted July 3, 2019 Report Share Posted July 3, 2019 Visit Asus Flash Tool Quote Link to comment Share on other sites More sharing options...
viralhax Posted July 6, 2019 Report Share Posted July 6, 2019 Android Multi Tools Quote Link to comment Share on other sites More sharing options...
viralhax Posted July 6, 2019 Report Share Posted July 6, 2019 Android Multi Tools Quote Link to comment Share on other sites More sharing options...
cindy8559 Posted October 17, 2019 Report Share Posted October 17, 2019 Thanks for the article, Maybe you want to know gpa calculator Quote Link to comment Share on other sites More sharing options...
danR Posted November 30, 2019 Report Share Posted November 30, 2019 HI.....I am building my first water cooled system I am using an intel i9900KS and a aorus 2080ti 11gb waterforce GPU. I was under impression tht I could use the soft tube cooling kit and a single pump that I purchase in the kit linked below. IS that correct? I am trying to anticipate how the tubing is going to be set up. It seemed to me tbat the pump only had a single input and output from the pics online. ANyoe able to give me some guidiance how this singlle kir will cool a cpu and a gpu? is there some schematic somewhere to expalin how to set it up? thanks in advance... Thermaltake Pacific C360 Ddc Res/Pump 5V Motherboard Sync Copper Radiator Soft Tube Water Cooling Kit Quote Link to comment Share on other sites More sharing options...
Ashgeeky Posted January 22, 2020 Report Share Posted January 22, 2020 Android Multi Tools Quote Link to comment Share on other sites More sharing options...
mohsin99 Posted February 12, 2020 Report Share Posted February 12, 2020 Nice article download Spotify Apk for more info. Quote Link to comment Share on other sites More sharing options...
alexharry07 Posted March 11, 2020 Report Share Posted March 11, 2020 Really good apps. especially I like Ogyoutube Apk. You just need to tap on the Red Download Button and your Ogyoutube app will start to download. Quote Link to comment Share on other sites More sharing options...
mickeysingh Posted March 23, 2020 Report Share Posted March 23, 2020 You must read this post about android pattern unlocking which can be done by this fast tool. Quote Link to comment Share on other sites More sharing options...
Rojin Posted May 1, 2020 Report Share Posted May 1, 2020 Hey. Where is the pump connected to? I know one goes to a fan connector. What about the the fat 2 pin cable? Quote Link to comment Share on other sites More sharing options...
Shantanu Posted May 15, 2020 Report Share Posted May 15, 2020 If you are looking for colors, visit Image color picker Quote Link to comment Share on other sites More sharing options...
otpbypass Posted July 9, 2020 Report Share Posted July 9, 2020 Here you can check that how you can bypass otp of any website or app. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.