Jump to content

Recommended Posts

Guest Tt Josh
Posted

No I didn't send any email to Thermaltake Customer Servise. Because my problem solved. Laser optical sensor has changed by technical warranty service. I 'll write to here if I encounter a new problem. Thank you again for your help.

Glad the issue has been resolved! ;)

 

Fire us a message again if you need assistance! ;)

  • 2 months later...
Posted

Hi, My mouse was working just fine. I was on a month long vacation and now it has suddenly stopped working. I'm facing the same issue. The buttons are working just fine, just the sensor is not working normally but it responds when I lift the mouse a few millimeters above the mousepad. I have tried all the methods mentioned before without success. Any sort of help would be highly appreciated. 

Guest Tt Josh
Posted

Hi, My mouse was working just fine. I was on a month long vacation and now it has suddenly stopped working. I'm facing the same issue. The buttons are working just fine, just the sensor is not working normally but it responds when I lift the mouse a few millimeters above the mousepad. I have tried all the methods mentioned before without success. Any sort of help would be highly appreciated. 

Hi, are you using Windows 10? or you can try to adjust the lift off.

 

TT ESPORTS SENSOR ON LIFT OFF TOOL V 1.0.0.1

 

Install that and see what happen.

 

We are going to release a new updated version for the software end of September. :)

Posted

Hi, are you using Windows 10? or you can try to adjust the lift off.

 

TT ESPORTS SENSOR ON LIFT OFF TOOL V 1.0.0.1

 

Install that and see what happen.

 

We are going to release a new updated version for the software end of September. :)

 

Thanks for the quick response. I'm on Windows 7 and I have tried the lift off tool without any success. Lift off tool increases the mouse sensor detection x distance plus the default sensor detection distance. My problem is default sensor detection distance is greater than the distance between the mouse pad surface and the sensor, hence it is not recognizing it. If i hover the mouse above the pad, it is working. I need to decrease the default sensor detection distance.

Guest Tt Josh
Posted

Thanks for the quick response. I'm on Windows 7 and I have tried the lift off tool without any success. Lift off tool increases the mouse sensor detection x distance plus the default sensor detection distance. My problem is default sensor detection distance is greater than the distance between the mouse pad surface and the sensor, hence it is not recognizing it. If i hover the mouse above the pad, it is working. I need to decrease the default sensor detection distance.

or try to reinstall the software again?

Posted

or try to reinstall the software again?

 I have tried uninstalling and installing the AP software, changed the firmware to v 1.1 and back to v 1.3, I have tried all the methods mentioned before in this post without any success. The strange this is it was all fine and it was stored away in it's pouch in a safe location, so I highly doubt the sensors were damaged suddenly.

Guest Tt Josh
Posted

Our new software will be coming out this end of September and you can try to install that once it's ready :)

 

Sorry for the inconvenience caused. :)

Posted

I have been using this mouse and it has been working great for me. However lately the back/forward buttons are not working properly for me. I tried to update however when i launch the new version i get an error saying "Please plug-in Gaming Device to start the AP Configuration !. Any help is appreciated! I downloaded the drivers from here and none of them have been able to find the device on my WINDOWS 10 Laptop. Thanks for the input and hopefully I can get this resolved on Windows 10. I'm wanting to buy one more of these for my work but need this to work first.

http://www.ttesports.com/Mouse/28/THERON/productPage.htm?a=a&g=ftr#.Vd41iPZVhBc

This is my model/mouse: http://www.amazon.com/Tt-eSPORTS-Thermaltake-Infrared-MO-TRN006DTM/dp/B00EVVNMQI

 

Turns out my mouse is the infared model with the MO-TRN006DTM. So re-installed that driver and everything is working properly now. Must have been the ugpraded that messed it up.

Guest Tt Josh
Posted

I have been using this mouse and it has been working great for me. However lately the back/forward buttons are not working properly for me. I tried to update however when i launch the new version i get an error saying "Please plug-in Gaming Device to start the AP Configuration !. Any help is appreciated! I downloaded the drivers from here and none of them have been able to find the device on my WINDOWS 10 Laptop. Thanks for the input and hopefully I can get this resolved on Windows 10. I'm wanting to buy one more of these for my work but need this to work first.

http://www.ttesports.com/Mouse/28/THERON/productPage.htm?a=a&g=ftr#.Vd41iPZVhBc

This is my model/mouse: http://www.amazon.com/Tt-eSPORTS-Thermaltake-Infrared-MO-TRN006DTM/dp/B00EVVNMQI

 

Turns out my mouse is the infared model with the MO-TRN006DTM. So re-installed that driver and everything is working properly now. Must have been the ugpraded that messed it up.

Glad the issue has been fixed :)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...